General

Cat ap255e paver for sale

Cat ap255e paver for sale

Cat ap255e paver for sale

I have a set of 6 catapillars which I need to remove.

They are not the correct size as you can see from the pictures.

Any ideas what size they would be?

The hole is 25mm

Also it would be nice if someone could send me some tips as I'm very bad with power tools.

Thanks.

Re: catapillars for sale

Thanks for your help,

I did try the calculator but it didn't work.

I measured all the pieces of the paving and came up with these figures, however the size is off. The one on the left is actually the right size, the one on the right is 1.5 times bigger.

You were right, the calculator did not work.

Can you suggest something, it's been driving me mad trying to figure this out.

Re: catapillars for sale

Hi there

The size of the hole in the capillary is 25 mm so you need to get the capillary with a size of 25mm to fit into the hole.

It is not a good idea to mix the sizes up, because it may affect the colour and the overall appearance.

The easiest way to find the right size capillary is to cut the capillary to size, and place the capillary into the hole in the paver, and then try to fit the capillary back into the hole. The way it sits into the hole will tell you the size.

The capillary may need to be moved to see if it is sitting strght, and also moved to see if there is enough room in the hole.

Re: catapillars for sale

Hi there,

Just to clarify the calculator is for finding the size of your muck, it's not really meant for finding the size of a capillary that will fit into a 25mm hole.

It should have a 25mm hole for the muck to fit in, so the hole is at the top.

The capillary hole is usually just smaller than the size of the hole in the paver, so 25mm or 26mm is the right size for most capillaries.

If your capillary is the wrong size for the paver, the paver may need to be cut a few mm down the sides.

Re: catapillars for sale

I've now got some of the old capillary out and it is actually the correct size. It is about 25mm and the hole is 25mm.

The holes are still not centered in the caps. I think I will need to get a grinder and get them cut.

I still don't know how I'm meant to take the capillary out of the muck.

Re: catapillars for sale

Originally Posted by carl_j

I've now got some of the old capillary out and it is actually the correct size. It is about 25mm and the hole is 25mm.

The holes are still not centered in the caps. I think I will need to get a grinder and get them cut.

I still don't know how I'm meant to take the capillary out of the muck.

Hi there

The holes are off center when they are assembled. If you need to cut them out, you will need to disassemble them first and then cut the capillary down to size.

Make sure you cut out a centimeter or so all the way around each hole so that you can get the capillary out with minimal damage.

You will then need to centre the holes on the capillary.

I used to be a power tool instructor and I can give you some tips.

Do make sure you do a good clean up when cutting, as this will be one of the most important things, and if you don't then you may end up with a mess.

If you are using a grinder to cut the capillary, you need to take the following precautions.

You will need to make sure the paver is in the correct position, so that you are holding the paver up from the ground.

You will need to hold the paver steady, so you don't get a twist of the paver around the edge of the hole.

You will need to ensure you hold the paver steady, but don't press down too hard on the paver, or you may split it.

You will need to ensure you do a good clean up, and this will be one of the most important things, but it is very easy to get a mess if you don't.

You will need to use a good quality cutting blade that is not too blunt, because this will make it easier to cut.

Try not to move your blade around too much, and try to hold it still.

Try to keep the blade clean, and do it on a clean surface, because a dusty blade will not work well.

Try not to touch the paver when you are using the cutting blade.

Try not to hold the paver so it is vertical, but try to hold it so that it is horizontal.

Try to ensure the paver is flat on the bench, because you need it to be smooth to cut.

When cutting a capillary that is smaller than the hole in the paver, you will need to try and use a circular saw, and this will make it easier, as the saw will do most of the work.

I would not recommend trying this with a jigsaw or an oscillating saw.

When using a circular saw, you will need to ensure that the saw is clean, and that the paver is flat and smooth.

When using a jigsaw or an oscillating saw, you will need to ensure you don't move the blade around too much, and you will need to hold it still.

If you are using a saw with a sharp blade, it may take a little longer, but it is


Watch the video: Cat AP255E Track Asphalt Paver. Visibility (December 2021).